Planar Biaxial Testing Guide

Home/Planar Biaxial Testing Guide

Planar biaxial testing applies force in both the x and y directions, allowing researchers to analyze the anisotropic behaviors of materials.  Biaxial test results can help manufacturers find the right material at the right quantity without quality loss in their products.

Forces in uniaxial and biaxial testing are shown in the two figures below. When tested biaxially, four perpendicular forces are applied to the specimen; due to the material anisotropy, the weaker region will fail quicker than other regions the same force is applied to.

Uniaxial and Biaxial stress states

Uniaxial and Biaxial stress states

Planar Biaxial Testing Specimen Geometry

Biaxial testing is often performed on flat, cruciform shaped specimen, where the four arms of the specimen are pulled by the four perpendicular forces shown above.  This allows a homogenous strain distribution in the thickness direction yielding in the center of the specimen which is then further investigated. The cruciform shaped specimen can be prepared in multiple variations; curved arms, straight arms, or with slits to avoid flexural forces in the plane of interest, shown below.

Cruciform Planar Biaxial test samples

Cruciform planar biaxial test samples

Planar biaxial test samples with prepared slits

Planar biaxial test samples with prepared slits

Note that forces can be applied at the same magnitude as well as at a variety of magnitudes in different directions. The stress distribution and the influence of such misalignment can be studied for further analysis.

Planar Biaxial Specimen Material

Types of materials tested in biaxial loading include soft biological tissues, silicone elastomers, composites, metal sheets, films, coated fabrics, and textiles, all subjected to orthogonal stress-strain fields. Test specimens are often prepared as explained in the section above. To adequately characterize the mechanical properties and the stress-strain behavior of the material, specimens are biaxially tested under force or deformation control with a configured planar biaxial testing machine and software.

Planar Biaxial Testing & Equipment

The primary reason for running biaxial tests, as opposed to running standard tensile tests, is to determine a specimen’s mechanical properties in its different points and analyze the stress and strain distribution. To do so, a planar biaxial testing system with multiple actuators that can also be configured with different strokes and speeds is used. Each actuator represents the different axes of the planar biaxial test and moves in equal or opposite directions so that the sample center point remains stationary. First, the biaxial specimen is mounted on the tester and the arms are clamped. We recommend securing two opposite sides first to ensure proper alignment. ADMET offers special biaxial grip and fixture setups and a variety of techniques, including suture racks, clamps and pin arrays, to match specimen dimensions and geometry as well as planar biaxial test setups with fluid baths and optional temperature control.

Biaxial testing systems can be equipped with various load cell capacities and strain measurement devices including contact and video extensometers to provide accurate force-strain data. Contact extensometers mount on the load frame and the slide mounting brings the extensometer into contact with the cruciform specimen. ADMET biaxial extensometers are capable of measuring combined in-plane strains of biaxial specimens while eliminating crosstalk between axes. Contact extensometers can also be configured for use in high temperatures.

Video extensometry is also often used in biaxial testing applications. Non-contact video extensometers are able to measure variables such as 3D displacements, strain, strain rates, velocities, as well as user-defined variables of cruciform specimens and specimens with complex geometries under complex loading conditions.

ADMET VeX Video Extensometer

ADMET VeX Video Extensometer

Samples can be loaded in static or cyclic fatigue tension, compression, flexion, or shear using the MTESTQuattro testing software to run planar biaxial test procedures where each axis is programmed for independent or coordinated motion under force or deformation control. The MTESTQuattro controller provides a camera trigger output for syncing test data with third party microscope/camera images. At the end of the tests, test reports are created automatically based on selected analyses.

Contact us today!

Need to find the right planar biaxial test equipment?

Our engineers are ready to help you!
Contact us today!
By |August 21st, 2018|Test How To's|Comments Off on Planar Biaxial Testing Guide